Title

TFX

Track editor
SHIFT+RETURN Start editing actual sector
C=+X Exchange actual channel with set
C=+S Save the current cursor position (1-5)
C=+G Recalk saved cursor position (1-5)
C=+M Number of music (1-8)
C=+@ Insert all from cursor to end into buffer
C=+* Paste the clipboard at the current position
C=+<- Play actual 3 sectors
<- Play in trace mode from the start of the song
SHIFT=+<- Start tracing the currently playing song
RETURN Go down to the next line
C=+ + Track+ – one note up
C=+ – Track- – one note down
C=+E End – end of playing
C=+L Loop xx – Jump to line xx

Sector editor
SHIFT+V Voice On/Off – If on, pressed note sounds with actual instruments, else doesn’t play
<- Play sector
= Toggle Symbolic/Numeric view of variables
SHIFT+C=+<- Cursor follow actually played note
C=+<- Play from cursor to end
SHIFT+<- Infinite play – sector plays roundabout
SHIFT+N/M Increases/Decreases all notes from cursor to end one note up/down
/ Fast up/down – Cursor jumps over 4 lines up/down
SHIFT+RETURN Return to track editor
C=+ up/dn Copy from current position to clipboard
C=+ * Paste at the current position
C=+ 1,2,3 Instrument Mode #1/2/3 (not in command mode)
C=+ 1..6 Set table variable n
C=+ 7 Set the filter frequency
C=+ 8 Set the filter type
C=+ P Set the pulse width
C=+ Y Set the auto-gate timeout to X frames
C=+ ,/. Go to the next/previous sector
C=+</> Edit another sector
C=+ + END of sector
C=+ – — pause (one tone delay)
C=+L GATE
C=+D DUR 00-3F – length of note
C=+V VOL 0-F – volume for actual channel
C=+B FVOL – Global volume for all channels
C=+Q,W ADN/RSN – AD/SR for following note
C=+A,S AD/SR – AD/SR for actual note
C=+R,T FF/FT – Filter frequency/type (in instrument must be filter on)
C=+I AUTOGATE
C=+P SETP – set pulse hi/lo
C=+J,K FADE+/- – For all channels, the highter value, the longer time
C=+G GLIDE – fluently goes from actual note to following (with the same intruments!). Must be last in list of commands
C=+H SLIDE – fluently goes from previous note to actual. Must be last in list of commands
C=+X SWITCH – from actual note (dosn’t work adsr, only changes frequency Command is witched of with second switch command)

Instruments commands
SHIFT+RETURN Switch between Table / Instrument editor
RETURN Go back to the place from whence you came
C=+P Save current instrument
C=+L Save all instruments
C=+O Load instrument into the current position
C=+K Load all instruments
C=+F Find next set of empty positions in the tables, and sets the current instrument to use them

Pulse table
C=+H HRD – Enter ‘Hard Note Mode’
C=+U USE – Use variable X
C=+Q, W, E SLO/SHI/SHL xxx xx xx … – Sets frequency of sound (LO for ultrasoft additions, HL for medium-soft and HI for soft additions) keys dont affect sound frequency, all keys are the same note. Used, e.g. for drums
C=+Z,X,C RLO/RHI/RHL – relative frequency of sound – used for user – defined vibrato
C=+R AD – Set the attack/decay register to X
C=+T SR – Set the sustain/release register to X
C=+G JWG – Jump to position X *if* the note is currently held
C=+N NRM – switches off sxx and rxx commands. All values under these commands are else not notes like normally
C=+S SET – sets pulse value
C=+A ADD xx yy – loop that increases value xx to actual value up to new value =yy
C=+B SUB xx yy – decrease loop
C=+D DEL – delay (1 frame)
C=+J JMP xx – jump to line xx